How To Enclose A Clawfoot Tub

how to enclose a clawfoot tub

Searching for how to enclose a clawfoot tub? Here, you’ll get all the necessary answers.

A clawfoot tub is a classic piece of bath furniture that has been around for centuries. It’s a deep, wide tub with a curved edge on one side and a square edge on the other. The curved side is perfect for soaking in, and the square edge is perfect for washing your feet. If you’re looking for an elegant way to relax after a long day, consider enclosing your clawfoot tub with a shower enclosure.

Materials and Tools

There are a few materials and tools that are necessary in order to enclose a clawfoot tub. This includes a sturdy frame, carpeting or padding, screws, nails, and a drill.

It is important to choose the right frame for the tub. The size of the frame will determine how much carpeting or padding is needed. It is also important to make sure that the screws and nails are long enough to reach all the way through the flooring.

Once the tub has been assembled, it is time to attach the carpet or padding. This can be done by using screws and nails or by using Velcro straps. Once everything is attached, it is time to drill holes in the bottom of the tub so that the water can drain properly.

Step-by-step instructions: How to enclose a clawfoot tub

If you’re considering enclosing a clawfoot tub, there are a few key steps you’ll want to take into account. First, make sure the tub is level and plumb. Next, build a frame around the tub that’s at least 2 inches larger on all sides than the tub itself. Finally, use drywall screws and sealant to attach the frame to the tub’s surface. Here are step-by-step instructions for enclosing a clawfoot tub:

  1. Measure the tub’s perimeter and subtract the needed amount of insulation (usually 2-3 inches).
  2. Cut the insulation to fit and attach it with screws or nails.
  3. Place the membrane over the insulation and screw it in place.
  4. Cut a hole for water drainage on one side of the membrane, being sure to leave a 1-inch border all around the edge of the opening.
  5. Cut a rectangle out of old sheetrock or wallpaper that is large enough to cover the entire front surface of the tub (including both sides of your cut hole).
  6. Carefully peel off the old paper and put it on your new membrane liner, making sure to line up all cuts and holes correctly.

How to enclose a clawfoot tub with glass

If you’re looking for a clawfoot tub glass enclosure, there are a few ways to do so. You can buy an enclosure kit, or you can make your own.

The most basic way to enclose a clawfoot tub is with a piece of glass that fits snugly around the outside of the tub. You’ll need to measure the dimensions of your tub before you start, and then purchase a piece of glass that’s the same size as the tub.

To install the glass, first, remove the old trim around the edge of the tub. Then, using a glass cutter or sharp knife, cut out a hole in the center of the glass that’s large enough for the drain pipe and large enough to fit around the bathtub rim.

Pros and Cons of Enclosing a Clawfoot Tub

When considering whether or not to enclose a clawfoot tub, there are a few benefits and drawbacks to consider. The benefits of enclosing a clawfoot tub include:

  • Security: A clawfoot tub can be easily secured with locks and bolts, making it less likely that it will be stolen or vandalized.
  • Cleanliness: Enclosing a clawfoot tub makes it easier to keep the water clean since dirt and debris cannot easily accumulate on the surface.
  • Health Risks: Clawfoots are made from soft materials which can collapse if wetted and drained incorrectly, posing health risks if the water is contaminated.
  • Cost: Enclosing a clawfoot tub can be expensive, but this added security may be worth the expense.

There are also some drawbacks of enclosing a tub as well, which are:

  • It can be difficult to get the tub out if it needs to be taken down for repairs or replacement.
  • The enclosure can make it difficult to keep the tub clean and free of debris.
  • If the enclosure is not properly installed, water can seep through the walls, leading to mold and mildew problems.

What kind of shower curtain do you use for a clawfoot tub?

When you are ready to tile or enclose your clawfoot tub with a shower curtain, there are a few things to consider. The size of your tub and the style of your shower curtain will both affect what type of curtain you should use.

One popular style is a tie-back curtain that hangs from rings on the sides or top of the tub. This style is perfect for small or medium-sized tubs that have standard-height walls. Tie-back curtains also come in a variety of lengths, so you can choose one that covers the entire tub or just part of it.

If you have a large or extra-long tub, an enclosure panel may be more suitable. Enclosure panels are made from sturdy vinyl material and cover both sides of the tub. They are available in several sizes and can be mounted using wall mounts or suspended from hooks in the ceiling.

Read More: How to get fish oil smell out of clothes

Final thoughts

A clawfoot tub is a luxurious and relaxing addition to any bathroom. Whether you’re looking to soothe your tired muscles after a long day or simply want to soak in some peace and quiet, a clawfoot tub is a perfect way to get your needs met.  We hope now you know all about clawfoot bathtub shower enclosures. Thanks.

Roger Walker
Roger Walker
Roger is a long-time homeowner with an enthusiasm for DIY, gardening, and design. He has over eight years of experience as a lifestyle editor and has worked with some of the top brands in the industry. Roger's goal is to help people make their homes comfort, functional, and beautiful- all while saving money.

Leave a Comment

Your email address will not be published. Required fields are marked *